Wavlink AC1200 Outdoor Extender

Step-By-Step Guide for the Wavlink AC1200 Outdoor Extender:

  • Once your wavlink Aerial HD4 has been unpacked, turn it on.
  • After pushing the power button, watch for the power LED to turn solid green.
  • Do not forget to maintain the booster near the router.
  • Use the Ap extender setup ext to connect.
  • Open any web browser, type or Ap.setup, and hit the enter key.
  • Enter your personal information to log in.
  • To finish the installation, adhere to the instructions.
  • At this point, you can disconnect your repeater and move it to its new place.

Note: That is how the Wavlink AC1200 Setup process is manually finished. Let’s attempt the (WPS) setup if the manual setup doesn’t work for you.

Read Also: WavLink Not Connecting to Internet? Let’s Help You Fixing it!

Wavlink AC1200 Setup Via WPS Method:

Let’s have a look at the WPS method, which is purported to be the quickest and easiest way to set up your Wavlink repeater. Without supplying a username, password, or SSID, you may set up your Wavlink AC1200 Outdoor extender Setup in less than two minutes after finishing the WPS setup. Now let’s look at the operation of the WPS method.

How to set up the Wavlink AC1200 using WPS: Step-By-Step guide

  • Get your Wavlink Outdoor Extender started.
  • Make sure the home router is in close proximity to it.
  • Please press the WPS button on your booster.
  • Now press the same WPS button on your home router.
  • It indicates that your repeater has been configured correctly when it shows three constant green lights.
  • The repeater is detachable, so you may put it anywhere you like.
  • That completes the WPS configuration for the Wavlink AC1200.

Wavlink AC1200 Extender firmware Upgrade Guide

If you are experiencing any problems with your Wavlink AC1200 extender (such it isn’t giving you the speed you want or something else), you will need to update the firmware. Along with other new features that will allay your worries, it offers extra security features.

To update the firmware on your Wavlink AC1200, take the following actions:

  • Get your Wavlink AC1200 started.
  • Think about any kind of mobile device.
  • Proceed to Ap.setup.
  • After choosing settings, choose firmware upgrade.
  • To finish the firmware upgrading process, adhere to the instructions.
  • Please don’t unplug the booster while it’s taking a minute.

Wavlink AC1200 Reset Guide

You must do a Wavlink AC1200 factory reset on your booster if you have forgotten your admin password or login and would like to retrieve it. The Wavlink AC1200 resets all of your personal data, including usernames, passwords, and SSIDs, to get your extender ready for a fresh setup process. A paper clip or needle, or any other hard-pointed object, is required to complete the factory reset procedure.

You may reset the Wavlink AC1200 by doing the steps shown below:

  • Attach the Wavlink AC1200 to an electrical outlet.
  • Look for the factory reset button under a little hole.
  • It could be on the side panel of the repeater.
  • Using a paperclip, press the reset button for eight to ten seconds.
  • In a few seconds, it will automatically reboot.
  • This is your Wavlink ready for the new installation process.


Q: How do I reset my Wavlink AC1200 WiFi Extender?

A: Locate the reset button, usually on the extender’s bottom or side. Press and hold it for 10 seconds using a paperclip.

Q: What if I forget the password for my extended Wavlink AC1200 network?

A: Perform a reset, and during setup, create a new password for your extended WiFi network.

Q: Can I change the name and password of the extended network during

A: Yes, customize the SSID and password for your extended WiFi network during the setup process.

Q: How do I access the Wavlink AC1200 extender’s configuration page?

A: Open a web browser, type the extender’s default IP address (commonly, and log in with default credentials.

Q: What should I do if my connection is slow after Wavlink AC1200 extender setup?

A: Check for interference, adjust extender placement, and ensure it’s within range of the router for optimal performance.

Leave a Reply

Your email address will not be published. Required fields are marked *